** 15% OFF SALE **

Discount Applied At Checkout

Rev Limiters

Sort By

9 Products

Drag - DRL-300 Standard Rev Limiter

The DRL300 has an improved clamping capability, and more outputs than the DRL200. The DRL200 could clamp only 2 of our green (higher impedance) coils. The DRL300 can clamp up to 4 of our blue (low impedance) coils. This means it can be used on drag bikes, and many other applications it could not manage before (automotive HEI ignitions). In addition, the output stage has also added a separate kill input. This input works separate of the rev limiter and can function even when the rev limiter has no power. This will kill the spark whenever a 12V signal is applied to the input.

Potential uses include shift kill to kill ignitions during upshift, allowing for clutchless shifts. Instead of having to cut jumper wires to get the box to work with a particular application, and having only two choices, there are now 3 dip switches. These dip switches allow not only for a very wide range of applications (single fire thumpers to Harleys to inline 4s to 8 cylinders), but they also allow for the rev range to be adjusted from the standard 6000-12000. This means that new motorcycles with 12000+ rpm redlines can now be handled, as can applications where the limit needs to be set below 6000.

Product Features

  • Continuously adjustable from 6,000 to 12,000 rpm Helps prevent engine failure
  • Prewired and easy to install

DRL-400 Two-Stage Rev Limiter

The Dyna DRL-400 Two Stage Rev Limiter has been specifically designed to maximize launch performance and over-rev protection in drag racing. The DRL-400 allows a precisely controlled launch rpm limit to be set, while also guaranteeing against over-rev damage due to missed shifts or drive train breakage. Selection between the launch limit and the upper over-rev limit is usually made through the use of a clutch lever switch. Both rpm limits are adjustable via two knobs on the DRL-400. The DRL-400 constantly monitors the engine rpm with great precision and randomly deletes ignition pulses to hold the engine exactly at the desired rpm. The DRL-400 can hold a 270 horsepower engine to a steady launch rpm with less then +/- 50 rpm wavier. Other launch rpm limiters typically make the engine rpm waive through a pounding oscillation. This can be very hard on expensive racing components. The DRL-400 works with all inductive electronic ignitions on 2 and 4 cylinder engines. It is housed in a 3 3/4" x 2 3/8" x 1" plastic case with integral mounting flanges.

Product Features

  • Accurate launch limiting with 32 different settings Smooth, non destructive launch limiting
  • Adjustable high limit between 16 different settings

DRL-500 Multi-Function RPM Limiter

The DRL-500 Module is an add-on multi-function rev-limiter that will work with all +12volt inductive ignition systems. The DRL-500 cannot raise the stock rev-limit. The DRL-500 Module will not work with OEM capacitive discharge (CDI) ignitions.

Product Features

  • 4-Channel RPM Limiter, 100rpm resolution
  • Launch Limiter, 50rpm resolution, optional handlebar rpm switch
  • Vehicle Speed Limiter
  • Shift Kill Interrupt, 0° to 45° retard or kill, 30ms to 250ms interrupt time
  • RPM Activated Switches (x2)
  • USB Programmable
  • Status LED
  • Data Recorder: Hour Meter - Number of Engine Starts - Maximum Engine Speed - Seconds Near Rev Limit - Battery Voltage - Histograph of RPM


Description  Part Number
Inductive RPM limiter DRL-300
Magneto CDI RPM limiter DRL-300CDI  
2 stage rev limiter DRL-400
2 stage rev limiter HD DRL-400-HD
2 stage rev limiter HD EFI Models DRL-400-HD EFI
2 stage rev limiter 4 channel Universal DRL-500-UNI
2 stage rev limiter 4 channel Right Side +12V DRL-500-4R
2 stage rev limiter 4 channel Left Side +12V DRL-500-4L
Remote Switch for DRL-500 DRS-500